Custom Screens in Beverly Hills Belong on the Door Schedule, Not the Punch List

Most screen problems in a luxury remodel start the day the door package is ordered. The architect draws the openings, the builder frames them, the finish crew trims them, and somewhere near the end a homeowner asks about bugs. By then the plaster is cured, and the casing is on, so a screen housing has nowhere graceful to go. The result is a surface-mounted box on a freshly finished wall, a fixed frame screwed over a door meant to open wide, or a change order nobody budgeted. None of that is a product failure. It is a sequencing failure, and it is avoidable. When you plan custom screens in Beverly Hills at the design stage, the cost is a line on the door schedule. When you plan them at the finish stage, it becomes rework. This guide covers what to decide, when to decide it, and why Tashman Home Center treats screens as part of the door scope.

The Short Answer

Specify screens on the door schedule at design development, next to the doors they serve. That gives the framer the right recess and blocking, the electrician a power location for motorized units, and the finish crew one trim detail instead of a patch. Tashman Home Center, family-owned since 1961, supplies and installs every screen with trained in-house installers.

Why Late Screens Cost More Than Early Ones

The screen itself is the same product at any stage. What changes is the work around it, and these four places hurt most.

• Housing and track locations drive framing, so a late screen forces a surface mount where an early one would have been recessed.
• Motorized systems need power at the housing, and opening finished walls for wiring is slow, messy, and visible.
• Frame color, mesh, and hardware finish are simple to match before the doors are painted and much harder to match afterward.
• Casing and trim installed before the screen is chosen often get cut, patched, or replaced.

What to Decide at Each Stage

Treat the screen like any other piece of door hardware and walk it through four checkpoints.

1.  At design development, mark every operable opening on the door schedule and assign each one a screen type, or note deliberately that it needs none.
2. Before rough framing, confirm housing location, recess depth, track clearance, and power against the manufacturer's installation drawings.
3. Before finishes, choose mesh, frame color, and hardware finish alongside the door finish so the set reads as one product.
4. Before fabrication, verify final dimensions on site, because a custom screen is built to the opening as it stands, not as it was drawn.

Match the Screen to the Opening

Each opening type creates different demands on the plan, and each has a matching system. Getting that match right is the difference between a screen that disappears and one that draws the eye.

• French doors take a pair of retractable screens that meet at the center with a magnetic closure, so both doors stay fully usable.
• Multi slide patio doors need a screen track and housing that do not collide with the door stack, so draw both at once.
• Bifold doors fold into a stack whose depth and swing direction decide where the housing can sit.
• Very wide walls of glass are workable, because retractable systems can span panoramic openings up to 32 feet wide, as covered in our guide to screening oversized and multi panel doors in Beverly Hills.
• Entries pair well with a custom swinging screen door built to the finished opening, or with a security screen door in a powder-coated finish chosen to suit the entry door.

What It Costs to Get It Right

Retractable screens typically run $300 to $900 per door, and a complete system for a bifold or multi panel opening typically runs $1,200 to $3,500, depending on size and mesh. Those figures belong in the budget next to the doors, not in a change order after the walls close. Mesh choice also affects daytime glare and the view, so settle it with the owner during design, not on installation day.

The Spec Line Worth Adding to Every Door Schedule

Architects who want this handled in one pass can add a note beside each operable opening. A workable version reads: screen type, recessed housing location, power rough-in at the housing if motorized, frame color matched to the door frame, mesh selected with the owner, and dimensions verified on site before fabrication. One line like that turns an afterthought into a scheduled item and gives the builder something to price, order, and inspect.

What Each Party Gains

Specifying a screen early protects three people at once.

• The architect keeps the opening detail as drawn, with no surface-mounted housing breaking a finished wall.
• The builder avoids a late change order and a trim crew returning to a finished room.
• The owner gets screens that match the doors and are ready before the first warm evening.

Why Architects and Builders Bring Tashman Home Center In Early

Tashman Home Center is a fourth-generation family business, founded in 1961 and licensed in California under Contractor License 298720. Because we also supply the multi-slide doors, bifold doors, and windows these screens attach to, one team can coordinate the whole opening, from the door schedule to the final install. Our trained in-house installers measure on site, and we custom-make every screen to the measured opening. We can mark up plans, confirm housing locations against your framing drawings, and flag conflicts with door stacks while changes are still inexpensive.

Send Us the Door Schedule

Planning new construction or a remodel in Beverly Hills? Share your door schedule and plans with our team, and we will review screen options for each opening before framing locks the decisions in. Request a screen review and estimate, or call (323)-676-0700.